Catalog
OPTI-KLENS -- Always the most economical method of fulfilling your eye and eye/face wash need. Our OPTI-KLENS units have been packaged for sale by major suppliers around the world and have been tested and proven to meet the ANSI Standard which governs the eyewash industry. All are accepted by OSHA to fulfill their requirements. So be sure to specify OPTI-KLENS! Superior products at the most economical prices!

Opti-Klens I

The Opti-Klens I mounts behind the faucet spout. It remains out of the way for every day faucet use, but it is always there as a permanent eye wash station when needed. Delivers over .4 gallons per minute of water, qualifying as an eye wash. There is no plumbing required, and it installs easily onto any faucet, sink or basin.

Two of the most common adapters are packed with the unit, and if another adaptor is needed, a free exchange is offered.

 

Opti-Klens IE

The addition of the Eliminator Valve to the Opti-Klens I allows water temperature to be pre-set at the faucet and remain on. You now have a dedicated eyewash station with only tempered water available. For sink use, the water flow is activated by the use of the push through plunger on the Eliminator Valve. Push the plunger to the opposite side for water flow.

" You no longer turn the faucet off or on by the handles"

The eliminator valve may be added to any existing installation. To install, remove the aerator on the bottom of the fountain and screw on the eliminator. With the water on at the faucet, push the rod to one side where the water flows into the sink. Then adjust the temperature using the faucet handles to meet the tempered water requirement. Do not use the faucet handles to shut off the flow into the sink. Push the rod in the eliminator valve the opposite direction to stop the flow, then use only that rod to turn on the water flow. The eye/face wash will function at all times, with or with out water flowing into the sink.

Opti-Klens II Regular

The Opti-Klens II is for use on standard faucets. This unit mounts to the spout with two spray nozzles curving upwards. Delivering more than 3 gallons of water per minute, it does so at a reasonable height, qualifying as a full face wash. No plumbing required. Two of the most common adapters are packed with the unit. Other adapters are available from manufacturer.

For laboratory/gooseneck faucets, use the Opti-Klens II Lab

Opti-Klens IIE Regular

The addition of the Eliminator Valve to the Opti-Klens II allows water temperature to be pre-set at the faucet and remain on. You now have a dedicated eye/ face wash station with only tempered water available.

" You no longer turn the faucet off or on by the handles"

The eliminator valve may be added to any existing installation. To install, remove the aerator on the bottom of the fountain and screw on the eliminator. With the water on at the faucet, push the rod to one side where the water flows into the sink. Then adjust the temperature using the faucet handles to meet the tempered water requirement. Do not use the faucet handles to shut off the flow into the sink. Push the rod in the eliminator valve the opposite direction to stop the flow, then use only that rod to turn on the water flow. The eye/face wash will function at all times, with or with out water flowing into the sink.

 

Opti-Klens II Lab

OK-II Lab is for use on laboratory faucets, having a greater forward angle than OK-II Regular. With all the same features of the Regular, both units are stationary on faucet to reduce the risk of misalignment and non-compliance.

Opti-Klens IIE Lab

The addition of the Eliminator Valve to the Opti-Klens II Lab allows water temperature to be pre-set at the faucet and remain on. You now have a dedicated eye/ face wash station with only tempered water available.

" You no longer turn the faucet off or on by the handles"

The eliminator valve may be added to any existing installation. To install, remove the aerator on the bottom of the fountain and screw on the eliminator. With the water on at the faucet, push the rod to one side where the water flows into the sink. Then adjust the temperature using the faucet handles to meet the tempered water requirement. Do not use the faucet handles to shut off the flow into the sink. Push the rod in the eliminator valve the opposite direction to stop the flow, then use only that rod to turn on the water flow. The eye/face wash will function at all times, with or with out water flowing into the sink.

Eliminator Valve

The Eliminator valve may be added to any of the Opri-Klens I or II models. It allows water temperature to be pre-set at the faucet and remain on.

OPTI-KLENS 1M

OPTI-KLENS 1M is a wall mounted eye/face wash with a plumbed connection. If this is your requirement, check our quality and our prices. We offer a stainless steel bowl at a price less than charged for plastic from other makers.

 
(c)2003 Desert Assembly